!
Illustrative estimate only. Mix ratios below are commonly used UK trade rules of thumb for domestic, non-structural work (paths, patios, shed bases, fence posts). For foundations, structural slabs or anything checked by Building Control, order a designated mix (e.g. RC25/30) to BS 8500 from a ready-mix supplier or get advice from a structural engineer.

Concrete & Cement Mix Calculator

Work out how much concrete you need for a patio, shed base, footing or fence post, and how many bags of cement, ballast or ready-mixed concrete to buy.


metres
Enter a length greater than 0
metres
Enter a width greater than 0
mm
Enter a depth greater than 0 Typical: patio ~75-100mm, shed base ~100-150mm
mm
Enter a diameter greater than 0
mm
Enter a depth greater than 0
Enter at least 1
metres
Enter a length greater than 0
mm
Enter a width greater than 0
mm
Enter a depth greater than 0
%
Covers spillage, an uneven base and over-digging. 10% is typical.
Check the yield printed on your chosen bag – it varies a little by brand.
GBP
GBP
GBP

Materials Breakdown

Mix Ratio Reference

How This Calculator Works: Volume is calculated from your project dimensions, then a wastage allowance is added. For bagged pre-mix, the volume is divided by the stated bag yield. For a DIY mix, quantities use commonly used UK trade cement and ballast figures for each ratio, by weight per cubic metre of finished concrete. Water is added gradually to reach a firm, workable consistency – there is no fixed figure, since it depends on the moisture already in your ballast.

Concrete & Cement Mix Calculator

Our Concrete & Cement Mix Calculator works out how much concrete you need for a patio, shed base, fence post or footing, then converts that into either bags of ready-to-use pre-mixed concrete or the cement and ballast quantities for mixing your own. It covers slabs, circular post holes and strip footings, and applies commonly used UK trade mix ratios – rules of thumb, not certified strength classes – for domestic, non-structural work.

How Much Concrete Do I Need?

Concrete volume is simply length x width x depth, converted into cubic metres. For a circular hole such as a fence post, it’s the area of the circle multiplied by the depth. Always add a wastage allowance – typically 10% – to cover an uneven sub-base, spillage and over-digging, since running short mid-pour is far more of a problem than having a little extra.

ProjectTypical DepthExample Volume
Garden path75-100mm1m wide x 5m long x 75mm = 0.375m³
Patio base75-100mm4m x 3m x 100mm = 1.2m³
Shed base100-150mm3m x 2.5m x 125mm = 0.94m³
Fence post hole450-600mm deep300mm diameter x 600mm = 0.042m³ per hole
Strip foundation450mm+10m x 0.3m x 0.45m = 1.35m³

How to Use This Calculator

  1. Choose your project shape – a rectangular slab, a circular hole (for fence or deck posts), or a strip footing/trench.
  2. Enter your dimensions – length and width in metres, depth in millimetres.
  3. Set a wastage allowance – 10% is a sensible default for most domestic jobs.
  4. Choose how you’ll get your concrete – bagged pre-mix (just add water) or mixing your own from cement and all-in ballast.
  5. For a DIY mix, pick a mix ratio that matches your job – general purpose, foundations, or driveway-strength.
  6. Click Calculate Concrete Needed to see your bag count, ballast quantity and an estimated cost.

UK Concrete Mix Ratios Explained

A mix ratio describes the proportion of cement to aggregate by volume. When cement is mixed with pre-blended all-in ballast (sharp sand and 20mm gravel together), it’s expressed as two numbers, such as 1:6. These are commonly used trade rules of thumb for domestic work – not certified strength classes:

RatioBest ForRule-of-Thumb Comparison (Uncertified)
1:6 (cement:ballast)Paths, patios, shed bases – general domestic use~C15/C20
1:5 (cement:ballast)Foundations and floor slabs~C20
1:4 (cement:ballast)Driveways and areas taking vehicle weight~C25

For anything load-bearing or inspected by Building Control – house extensions, structural foundations, retaining walls – these ratios are a useful guide only. Order a designated mix to BS 8500 (such as RC25/30) from a ready-mix supplier instead, since a shovel-and-bucket ratio can’t guarantee a certified strength.

Bagged Pre-Mix vs Mixing Your Own

  • Bagged pre-mixed concrete – dry cement, sand and aggregate already combined; just add water. Convenient for small jobs like fence posts, but works out more expensive per cubic metre than buying materials separately.
  • Mixing your own (cement + ballast) – buy cement in 25kg bags and all-in ballast by the tonne or bulk bag, then mix on site with a cement mixer or by hand. Cheaper for larger volumes but more labour-intensive.
  • Ready-mix delivery – a lorry delivers wet concrete ready to pour. Usually the most practical and cost-effective option above roughly 0.5m³, and gives consistent strength throughout, but most suppliers have a minimum order.

How Many Bags of Cement Per Cubic Metre?

The number of 25kg cement bags needed depends on the mix ratio – richer mixes (more cement relative to ballast) need more bags per cubic metre of finished concrete:

Mix RatioCement per m³25kg Bags per m³All-In Ballast per m³
1:6300kg12 bags~2.08 tonnes
1:5350kg14 bags~2.0 tonnes
1:4425kg17 bags~2.0 tonnes

Figures are the commonly used UK trade rules of thumb for site-mixed domestic concrete. Actual bag yields vary slightly by brand and by how much water the ballast already holds – check the manufacturer’s guidance where precision matters.

Frequently Asked Questions

How much concrete do I need for a patio?

Multiply the patio’s length by its width by the depth (typically 75-100mm for a domestic patio) to get the volume in cubic metres, then add roughly 10% for wastage. A 4m x 3m patio at 100mm deep needs about 1.2m³ before wastage, or around 1.32m³ once wastage is added.

What mix ratio should I use for a shed base?

A 1:6 cement-to-ballast mix (general purpose, commonly cited as roughly C15/C20 as a rule of thumb, not a certified strength class) is a common choice for a shed base, garden path or patio, since these only carry light static or foot loads.

How many 25kg bags of cement per cubic metre of concrete?

At the common 1:6 general-purpose ratio, roughly 12 x 25kg bags of cement per cubic metre of finished concrete, alongside about 2.08 tonnes of all-in ballast. A richer 1:4 driveway-strength mix needs around 17 bags per cubic metre.

Is it cheaper to mix my own concrete or buy ready-mix?

For small jobs – a few fence posts or a small patio – bagged pre-mix or a DIY cement-and-ballast mix usually works out cheaper overall once you account for a ready-mix supplier’s minimum order. For anything above roughly half a cubic metre, ready-mix delivery is often more cost-effective and saves a lot of physical mixing labour, though prices vary by supplier and location.

How much ballast do I need per bag of cement?

It depends on the mix ratio. At 1:6, each 25kg bag of cement pairs with roughly 170kg of all-in ballast. At 1:4 (driveway strength), each bag pairs with roughly 120kg of ballast, since the mix is richer in cement relative to aggregate.

What’s the difference between concrete and cement?

Cement is the fine grey powder that binds everything together once water is added. Concrete is the finished material: cement, sand and coarse aggregate (or all-in ballast) mixed with water. “Cement” and “concrete” are often used interchangeably in everyday speech, but a bag of cement alone will not make a usable slab without sand and aggregate.

How deep should a concrete slab be?

It depends on what the slab will carry. As a general guide, garden paths and patios are typically 75-100mm deep, shed bases 100-150mm, and driveways or anything taking vehicle weight are usually 100-150mm over a properly compacted sub-base, often with reinforcement. Structural slabs and foundations should be specified by a structural engineer or in line with Building Control requirements.

Do I need building regulations approval for a concrete base?

A small, freestanding garden shed base or path generally doesn’t need Building Control approval. However, larger structures, bases that form part of a building’s foundations, or work near boundaries and drains may fall under the Building Regulations. Check with your local authority’s Building Control department if you’re unsure before starting work.