Planning quantities, not prices. This calculator estimates decking boards, joists and fixings from your layout. Board sizes, gaps, joist spacing and allowances are editable example values. Always check them against your board manufacturer guidance and supplier before you order.

Decking Calculator

Work out how many decking boards, joists and fixings you need, and which board length wastes least.

1. Your deck

Enter each rectangular area. For an L-shaped deck, use two areas that do not overlap. The calculator treats every area as separate, so overlapping parts would be counted twice. You can enter positions below to have overlaps checked.

Deck area 1

m
m
Check that my areas do not overlap (optional)

Measure from one shared corner of the whole deck, with lengths running left to right and widths running top to bottom for every area. Fill in every area, or leave all blank. Areas that only touch along an edge are fine.

m
m
Cut-outs such as trees, planters or hatches (optional)

Distances are measured from the same corner of the area. Overlapping cut-outs are counted once. For straight decking, boards that a cut-out fully covers are removed, and boards it only partly covers are kept and notched. Diagonal decking assumes no board saving around cut-outs.

2. Decking boards

Starting values are examples. Use the dimensions of the boards you plan to buy.

mm

Example value. Check your product.

mm

Example value. Follow the manufacturer guidance for your boards.

Example lengths. Stock varies by supplier.

m
mm

Board joints are placed over joists, so this affects the layout. It also sets the sub-frame. Depends on board thickness and material, so check the manufacturer guidance.

%

Covers mistakes and damaged boards. Default 10%.

Both figures are always shown. Reuse is a best case.

mm

Offcuts shorter than this are treated as waste.

3. Sub-frame and fixings (optional)

Untick this if you only need the decking boards.

Example lengths. Stock varies by supplier.

m
%

Extra for cutting and defects.

Starting value is 2. Check your board guidance.

Leave blank to see item counts only.

%

Extra for dropped or snapped fixings.

Decking Calculator UK

This decking calculator works out how many decking boards you need, how many joists to build the frame, and roughly how many screws or clips to buy. Unlike a simple area calculator, it lays your boards out row by row, so it counts the offcuts from cutting boards to length and shows which board length wastes least for your deck.

How the decking calculation works

  1. Rows of boards. Rows across the deck = (deck width + gap) divided by (board width + gap), rounded up.
  2. Boards per row. Each row is laid out board by board. A board is cut back to the nearest joist so that every joint lands on a joist, and the last piece is cut to the end of the row.
  3. Offcuts. The conservative quantity treats every cut-off end as waste. The estimate with reuse shows the best case if suitable offcuts are used for other pieces. Both are always shown, and you choose which one the order is based on.
  4. Allowance. A wastage allowance is added for mistakes and damaged boards, then rounded up to whole boards.
  5. Joists and fixings. Joists are spaced evenly at no more than your chosen spacing, with one at each end. Fixings are counted at every point where a board crosses a joist.

Worked example

Take a 4.8 m x 3.0 m deck with boards running along the 4.8 m side, using 140 mm boards with a 5 mm gap and joists at 400 mm centres (example values). That gives 21 rows of boards. With 3.6 m boards, each row needs one full board that ends on a joist, plus a 1.2 m cut piece, so you need 42 boards if every offcut is treated as waste. If the 2.4 m offcuts are reused for other pieces, the best-case estimate falls to 28 boards, so treat 42 as the safer quantity. With 4.8 m boards, each row needs exactly one board, so you need 21. After the default 10% allowance, those three figures become 47, 31 and 24 boards. The frame needs 13 joists, each 3.0 m long, at 400 mm centres. That is 15 joists with a 10% allowance. With 4.8 m boards there are 273 board-to-joist crossings, so about 546 screws at two per crossing before any allowance.

What affects how much decking you need

  • Board length against deck length and joist spacing. A board length that divides neatly into the length of the deck, and ends on a joist, wastes very little. One that leaves a short remainder, or ends between joists, wastes a lot.
  • Board gap and width. A wider gap or narrower board means more rows to cover the same width.
  • Laying pattern. Diagonal boards produce more angled offcuts than straight boards, so the calculator uses a higher default allowance.
  • Cut-outs and shape. Boards a cut-out fully covers are removed. Boards it only partly covers are kept and notched. Overlapping cut-outs are counted once.
  • Joint positions. Where boards meet end to end, each end needs support. The calculator places joints over joists and shows how many joist lines carry a joint, plus the extra joists needed if you double them up. These extras are not included in the main joist total.

Straight against diagonal decking

FeatureStraightDiagonal
How it is calculated hereRow by row layout, joints over joistsFrom area, with a larger allowance
Default allowance10%15%
Offcut reuseShown as a best-case estimateNot modelled
Cut-outsBoards fully covered are removed, partly covered boards are keptNo board saving assumed
Joist spacingFollow the board guidanceCan need closer spacing, so check the guidance

Frequently asked questions

How many decking boards do I need?

Divide the width of the deck by the board width plus the gap to get the number of rows, rounding up. The calculator then lays each row out board by board, cutting boards so that every joint lands on a joist. It adds a wastage allowance and shows the total to order.

How much gap should I leave between decking boards?

It depends on the board material, thickness and the manufacturer guidance, so there is no single correct figure. This calculator starts at 5 mm as an example and lets you change it. Follow the instructions that come with your boards.

How much wastage should I allow for decking?

The calculator defaults to 10 percent for straight boards and 15 percent for diagonal boards, and you can change both. The layout already counts the offcuts from cutting boards to length, so the allowance is mainly for mistakes, damaged boards and awkward cuts.

What joist spacing should I use for decking?

Joist spacing depends on the board thickness, the board material and the manufacturer guidance. Diagonal boards can need closer spacing than straight boards. The calculator uses 400 mm as an editable starting value and places board joints over joists, so changing the spacing can change how many boards you need.

How many screws do I need for decking?

The calculator counts every point where a board crosses a joist, then multiplies by the screws or clips you choose for each crossing. It adds an allowance and can round up to whole packs if you enter a pack size. The result is an indicative planning figure, not a fixing schedule, so keep a few spare.

Which decking board length is best?

The best length is the one that leaves the least offcut waste for your deck size and joist spacing, and the comparison table shows this for common lengths. A board length that does not match your joist spacing has to be cut back to the nearest joist, which creates more waste.

Does the calculator allow for reusing offcuts?

For straight decking it shows two figures. The conservative figure treats every offcut as waste. The estimate with reuse assumes suitable offcuts are used for other pieces, which are all cut to land on joists. The reuse figure is a best case, so the conservative figure is the safer quantity to order. Reuse is not modelled for diagonal decking.

Does this calculator include posts, footings and ground preparation?

No. It covers boards, joists and fixings only. For post footings use the Concrete Calculator, and for a gravel or sub-base layer use the Aggregate and Topsoil Calculator.

Can I use it for an L-shaped deck or one with a tree or planter?

Yes. Add up to four rectangular areas for an L-shaped or multi-level layout. The areas must not overlap, and you can enter their positions to have the calculator check this. Cut-outs are optional. For straight decking, boards that a cut-out fully covers are removed, and boards it only partly covers are kept and notched. Diagonal decking assumes no saving around cut-outs.

Does it work for composite decking?

Yes, as long as you enter the board width, gap and length for your product. Composite boards often have their own spacing and fixing rules, so follow the manufacturer guidance and change the calculator inputs to match.

Do I need planning permission or Building Regulations approval for decking?

Sometimes. It depends on the height of the deck, where it is and the type of property. This calculator does not check this, so ask your local council or use the Planning Portal before you build.