!
This is an indicative planning estimate, not an EPC rating. A real EPC uses the government’s assessment methodology (RdSAP) and property-specific information that this calculator doesn’t collect. Trying to reverse-engineer an EPC score from a handful of inputs would give a false impression of accuracy — use this tool to explore options, then confirm with an accredited assessor.

EPC Rating & Improvement Cost Calculator

Get an indicative estimate of your home’s EPC band and explore what it might cost to reach a higher one. Enter your known EPC band if you have it, or let the calculator estimate a starting point from your property details.


Check the official EPC register if you’re not sure. If you enter a known band rather than its exact score, this calculator uses the midpoint of that band for its illustrative model — your actual score may be anywhere within the band.

EPC Scale (Indicative Model Score)

Potential Improvements

Untick any measure to remove it from the cost and outcome estimate below. These are potential improvements based on a simplified points model — not recommendations tailored to a full survey of your home.

If you’re a landlord: minimum energy efficiency standards (MEES) set the lowest EPC band a rented property can legally have, and proposed future rules would raise this further for privately rented homes. These requirements change, so always check the current position on GOV.UK’s MEES landlord guidance rather than relying on this or any other calculator.
How this calculator works: this calculator uses its own simplified illustrative points model. These points are NOT SAP/RdSAP scores and cannot reproduce an official EPC assessment. If you enter your known EPC band, that’s used as the starting point. If not, the model estimates a starting band from your property type, age, heating, insulation and glazing — clearly labelled as an estimate, not an official rating. Potential improvements are then scored using indicative model-point contributions and costed using typical UK installation price ranges, adjusted roughly for property size.
  • An official EPC can only be produced by an accredited domestic energy assessor using the government’s RdSAP methodology.
  • If you enter a known EPC band rather than its exact score, this calculator uses the midpoint of that band for its illustrative improvement model. Your actual EPC score may be anywhere within the band, so the resulting outcome is only an estimate.
  • Indicative point contributions and costs are illustrative ranges, not quotes — actual figures depend on your specific property, installer, specification and location.
  • Improvements are shown as potential options, not personalised recommendations.

EPC Rating & Improvement Cost Calculator 2026

Our EPC Rating & Improvement Cost Calculator gives you an indicative planning estimate of your home’s Energy Performance Certificate (EPC) band, and explores what a range of energy-efficiency improvements might cost to move towards a higher band. It’s designed for early-stage planning — deciding whether an upgrade is worth investigating further — not as a substitute for an official EPC assessment.

This Is Not an Official EPC Calculator

It’s worth being upfront about what this tool is and isn’t. An official EPC is produced by an accredited domestic energy assessor using the government’s RdSAP (Reduced-data Standard Assessment Procedure) methodology, which draws on a detailed on-site inspection: exact wall construction, floor area, room dimensions, boiler model, glazing specification and more. This calculator asks for a handful of general inputs and applies a simplified, transparent points model to produce an indicative estimate. It cannot and does not replicate RdSAP. If you need a valid EPC — to sell, let, or claim a grant — you’ll need an assessment from an accredited assessor, which you can arrange via the official EPC register.

How EPC Bands Work

Every EPC combines a letter band (A to G) with a numerical SAP score from 1 to 100. The bands are set by government and used consistently across the register:

BandSAP Score RangeTypical Description
A92 – 100Exemplary — usually new-builds with heat pumps and high insulation
B81 – 91Highly efficient — often extensively retrofitted or newer properties
C69 – 80Good — the level often referenced as a target for landlords and mortgage incentives
D55 – 68The most common band among existing UK homes
E39 – 54Below average — currently the legal minimum for most rented properties
F21 – 38Poor — typically older, poorly insulated properties
G1 – 20Very poor — usually little or no insulation and an inefficient heating system

These are the standard SAP score boundaries used across the EPC register. Always check the current rules on GOV.UK, since EPC methodology and related policy are subject to change.

How to Use This Calculator

  1. Enter your property details — type, approximate age, heating system, insulation and glazing.
  2. Enter your known EPC band if you have one. You can look this up on the official EPC register if you’re not sure. If you don’t know it, leave this as “I don’t know” and the calculator will estimate a starting band from your other answers.
  3. Choose a target band.
  4. Click Calculate to see potential improvements, each with an indicative cost and an estimated model-point contribution.
  5. Tick or untick measures to see how the estimated cost and outcome band change.

Potential Improvements Covered

The calculator considers eight common improvement measures, shown only where they’re relevant to what you’ve told it about your property:

  • Loft insulation — topping up or installing insulation where there’s currently none or only a partial depth.
  • Cavity wall insulation — for uninsulated cavity walls.
  • Solid wall insulation — internal or external, for uninsulated solid walls.
  • Double or triple glazing — where the property currently has single glazing.
  • Heating upgrade to a heat pump — where a heat pump isn’t already installed.
  • Heating controls — smart thermostats, thermostatic radiator valves (TRVs) and zoning.
  • Solar PV panels.
  • Draught proofing.

Each measure is shown as a potential improvement with an indicative cost range and an estimated model-point contribution — not a personalised recommendation, since that would require a full survey of your specific property. These model points are illustrative only and are not SAP or RdSAP points.

Why We Don’t Show a Single Exact Cost or Band

Actual improvement costs vary by property size, existing condition, installer, specification and region — sometimes considerably. Rather than inventing a single number, the calculator shows a cost range for each measure and for the total. In the same way, it never states that your home “will become” a specific band after improvements. Instead it shows an estimated outcome — “around Band C”, for example — with a clear caveat that this is based on a simplified model, not a guarantee.

EPC Bands and Landlords: MEES

Minimum energy efficiency standards (MEES) set the lowest EPC band a property can legally be let at in the private rented sector. There has also been discussion of raising this minimum standard for privately rented homes in future. Because these rules — and their timelines — are subject to ongoing government decisions and can change, this calculator doesn’t build in a specific current threshold or deadline. If you’re a landlord planning improvements around a compliance deadline, check the current position directly on GOV.UK’s MEES landlord guidance before relying on any figure from a calculator.

Improving Your EPC: General Principles

  • Fabric first: insulation (loft, walls) is generally the cheapest way to improve energy efficiency per pound spent, before considering heating system changes.
  • Combine measures: a single measure may only move a property partway between bands; combining insulation with heating or glazing upgrades is often needed to cross a band boundary.
  • Get quotes before committing: the ranges here are indicative only. Get at least three quotes from accredited or MCS-certified installers for any significant measure.
  • Check funding: some measures may be eligible for government grants or energy company schemes. Eligibility rules change, so check current schemes on GOV.UK rather than assuming based on older information.
  • Confirm your wall type: if you’re not sure whether your walls are cavity or solid, get this confirmed by a professional before budgeting for insulation, since the two measures differ significantly in cost.

Frequently Asked Questions

Is this the same as an official EPC rating?

No. This is an indicative planning estimate, not an EPC rating. A real EPC uses the government’s RdSAP assessment methodology and property-specific information that this calculator doesn’t collect, carried out on-site by an accredited domestic energy assessor. Use this tool to explore options, then confirm with an accredited assessor.

How accurate is the estimated starting band?

If you don’t know your current EPC band, the calculator estimates one using a simplified points model based on your property type, age, heating, insulation and glazing. This is clearly labelled as an estimate throughout, since a genuine assessment considers many more details than this calculator collects. If you have a recent official EPC, entering that band directly will always be more accurate than the estimate.

What is EPC Band C and why does it matter for landlords?

Band C covers SAP scores of 69 to 80. It’s often referenced as a target standard for privately rented homes, though the current legal minimum and any future requirements can change. Because this is an area of ongoing policy discussion, check the current rules on GOV.UK’s MEES landlord guidance rather than relying on any calculator for compliance purposes.

Do government grants cover these improvements?

Some insulation, heating and low-carbon measures are periodically covered by government or energy company schemes, but eligibility, funding levels and scheme dates change over time. This calculator shows costs before any grant, since grant eligibility depends on personal and property circumstances. Check current schemes on GOV.UK for up-to-date eligibility.

How is the estimated cost calculated?

Each improvement measure has an indicative UK cost range, adjusted roughly for property size (flats and terraces typically cost less than larger detached homes for the same measure). These are typical installed price ranges, not quotes. Actual costs vary by property, installer, specification and location, so always get multiple quotes before committing to any work.

Can solar PV improve my EPC rating?

Yes, solar PV panels can contribute to a higher EPC score, since the assessment accounts for on-site renewable generation. The calculator includes solar PV as a potential improvement with an indicative cost and estimated point contribution, alongside insulation, glazing and heating measures.

What’s the difference between cavity wall and solid wall insulation?

Cavity walls have a gap between two layers of brick or block that can be filled with insulation relatively cheaply and quickly. Solid walls have no such gap, so insulation has to be added to the inside or outside face of the wall, which is a larger, more expensive job. If you’re not sure which type your property has, it’s worth getting this confirmed by a professional before budgeting for either measure.

How do I get an official EPC assessment?

You’ll need to book an assessment with an accredited domestic energy assessor. You can find one, and check any existing EPC for a property, via the official EPC register on GOV.UK.